MICROCONTROLLER ATMEL MICROCHIP

Service Details:

ATmega48A/PA/88A/PA/168A/PA/328/P megaAVR® Data Sheet Introduction The ATmega48A/PA/88A/PA/168A/PA/328/P is a low power, CMOS 8-bit microcontrollers based on the AVR® enhanced RISC architecture. By executing instructions in a single clock cycle, the devices achieve CPU throughput approaching one million instructions per second (MIPS) per megahertz, allowing the system designer to optimize power consumption versus processing speed.Features ??? High Performance, Low Power AVR® 8-Bit Microcontroller Family ??? Advanced RISC Architecture 131 Powerful Instructions – Most Single Clock Cycle Execution 32 x 8 General Purpose Working Registers Fully Static Operation Up to 20 MIPS Throughput at 20MHz On-chip 2-cycle Multiplier ??? High Endurance Non-volatile Memory Segments 4/8/16/32KBytes of In-System Self-Programmable Flash program memory 256/512/512/1KBytes EEPROM 512/1K/1K/2KBytes Internal SRAM Write/Erase Cycles: 10,000 Flash/100,000 EEPROM Data retention: 20 years at 85°C/100 years at 25°C(1) Optional Boot Code Section with Independent Lock Bits ??? In-System Programming by On-c
ATmega48A-AU ATmega48A-AUR(5) ATmega48A-MMH(4) ATmega48A-MMHR(4)(5) ATmega48A-MU ATmega48A-MUR(5) ATmega48A-PU

ATmega48PA-AU ATmega48PA-AUR(5) ATmega48PA-MMH(4) ATmega48PA-MMHR(4)(5) ATmega48PA-MU ATmega48PA-MUR(5) ATmega48PA-PU 32A 32A 28M1 28M1 32M1-A 32M1-A 28P3 Industrial (-40???C to 85???C) ATmega48PA-AN ATmega48PA-ANR(5) ATmega48PA-MMN(4) ATmega48PA-MMNR(4)(5) ATmega48PA-MN ATmega48PA-MNR(5) ATmega48PA-PN
ATmega88A-AU ATmega88A-AUR(5) ATmega88A-MMH(4) ATmega88A-MMHR(4)(5) ATmega88A-MU ATmega88A-MUR(5) ATmega88A-PU


ATmega88PA-AU ATmega88PA-AUR(5) ATmega88PA-MMH(4) ATmega88PA-MMHR(4)(5) ATmega88PA-MU ATmega88PA-MUR(5) ATmega88PA-PU 32A 32A 28M1 28M1 32M1-A 32M1-A 28P3 Industrial (-40???C to 85???C) ATmega88PA-AN ATmega88PA-ANR(5) ATmega88PA-MMN(4) ATmega88PA-MMNR(4)(5) ATmega88PA-MN ATmega88PA-MNR(5) ATmega88PA-PN

ATmega168A-AU ATmega168A-AUR(5) ATmega168A-MMH(4) ATmega168A-MMHR(4)(5) ATmega168A-MU ATmega168A-MUR(5) ATmega168A-PU

ATmega168PA-AU ATmega168PA-AUR(5) ATmega168PA-MMH(4) ATmega168PA-MMHR(4)(5) ATmega168PA-MU ATmega168PA-MUR(5) ATmega168PA-PU Package(1) Operational Range 32A 32A 28M1 28M1 32M1-A 32M1-A 28P3 20 Note: 1.8 - 5.5 ATmega168PA-AN ATmega168PA-ANR(5) ATmega168PA-MN ATmega168PA-MNR(5) ATmega168PA-PN


ATmega168PA-AU ATmega168PA-AUR(5) ATmega168PA-MMH(4) ATmega168PA-MMHR(4)(5) ATmega168PA-MU ATmega168PA-MUR(5) ATmega168PA-PU Package(1) Operational Range 32A 32A 28M1 28M1 32M1-A 32M1-A 28P3 20 Note: 1.8 - 5.5 ATmega168PA-AN ATmega168PA-ANR(5) ATmega168PA-MN ATmega168PA-MNR(5) ATmega168PA-PN

Service Details:

8-Bit Universal MCU List:

• CS8100
• CS8101
• CS8301
• CS8302
• CS8706
• CS8706GP
• CS8775
• CS8775EO
• CS8776
• CS8776EP
• CS8776EO
• CS8K01PAGO
• CS8K01PBGO
• CS8K01PGN
• CS8L01
• CS8L01CN
• CS8L01P
• CS8L01PCN
• CS98P153ACO
• CS98P153ACP
• CS98P154ACO
• CS98P154ACP
• CS98P156CO
• CS98P156CP
• CS98P156ACO
• CS98P156BCO
• CS98P157CO
• CS98P157CP
• CS98P157ACO
• CS98P157ACP
• CS98P159CO
• CS98P159CP
• CS98P159ACO
• CS98P159BCO
• CS98P258GP
• CS98P258GO
• CS98P258AGO
• CS98P260EEO
• CS98P260EEP
• CS98P260BEO
• CS98P260BEP
• CS98P260AEO
• CS98P260AEP
• CS98P268AEO
• CS98P268AEP
• CS98P268BEO
• CS98P268BEP
• CS98P268CEO
• CS98P268CEP
• CS98P401AEN
• CS98P401BEN
• CS98P401CEN
• CS98P401DEN
• CS98P806

Service Details:

PD69208T4/PD69204T4/ PD69208M PoE PSE Manager Introduction Microchip's PD69208T4, PD69204T4, and PD69208M Power over Ethernet (PoE) manager ICs integrate power, analog, and state-of-the-art logic into a single 8 mm × 8 mm, 56-pin, plastic QFN package. The device is used in conjunction with a Microchip PSE controller or an Ethernet switch processor from a supported third-party vendor to provide an IEEE® 802.3af/at/bt or Power over HDBase (PoH) Power Sourcing Equipment (PSE) solution. Typical PoE Application The following figure shows the typical PoE application of Microchip Generation 6 devices. Figure 1 Typical PoE Application with Microchip Controller UART/I 2 C VSSA VSS VDDA VDD MOSI To Host PD69210 PD69220 PD69200 PoE Controller SCK xCS MISO Isola???on MOSI SCK xCS MISO IREF AGND DGND PGD<0:3> Power Supply Monitoring VAUX5 VAUX3P3 VMAIN 5V 3.3V VMAIN PD69208T4 PD69204T4 PD69208M PoE Manager VMAIN VMAIN PORT_NEG0 PORT_NEG7 (PD69208T4/M) PORT_NEG3 (PD69204T4) Required for IEC62368-1 Ed.2 PSYSTEM>250W System Bulk Capacitor Required for IEC62368-1 Ed.2 PSYSTEM>250W F F Consult Microchip AN3361 Designing an IEEE 802.3af/at/bt PoE System Based on PD692x0/PD69208. © 2020 Microchip Technology Inc. Datasheet DS00003428C-page 1 PoE Manager Features • Drives 2-pair or 4-pair power ports • Single DC voltage input • Built-in 3.3 V and 5 V regulators • Over-temperature protection and thermal monitoring • Low-power dissipation • Industrial temperature range: –40 °C to 85 °C • MSL3, RoHS compliant Table 1.???Device-Specific Features Feature PD69208T4 PD69204T4 PD69208M Ports per IC 8 4 8 PSE type supported 4 4 3 Maximum output power 95 W 95 W 60 W Chipset Features • Complies with IEEE 802.3af/at/bt • Supports Power over HDBaseT (POH) • Cascade up to 12 PoE devices for 48 logical ports • Advance system power management • Emergency power management supporting 16 configurable power banks • Continuous port monitoring and status • Supports Fast and Perpetual PoE • Supports pre-standard PD detection • LED stream support • Configurable load current setting • Field upgradable • Any combination

Service Details:

IC MCU 8BIT 256KB FLASH 100TQFP
AVR series Microcontroller IC 8-Bit 16MHz 256KB (128K x 16) FLASH 100-TQFP (14x14)

Service Details:

PIC series Microcontroller IC 8-Bit 40MHz 32KB (16K x 16) FLASH 40-PDIPPIC18F4520-I/P

Additional Information:

• Delivery Time: 2
• Packaging Details: tube

Service Details:

PIC series Microcontroller IC 8-Bit 40MHz 48KB (24K x 16) FLASH 64-TQFP (10x10)     ............... 

Additional Information:

• Production Capacity: 50000
• Packaging Details: TRAY

Service Details:

Megawin Technology Co., Ltd. is headquartered at the Taiyuan Science Park in Taiwan, and primarily focuses on MCU design and sale. Megawin Technology was formed by a group of intellectual MCU software/hardware platform specialists and provides full services in every MCU field. Megawin Technology equips with not only variable IC product lines but also complete development solution tools, such as ICE, Writer, and ISP Programmer. In response to energy conservation and carbon reduction. For IC operating conditions, we target higher immunities, wider operation voltages, and larger operation temperature ranges. We are adding more analog modules to IC to conveniently capture natural signals, and also to build more serial interfaces to convert to digital signals. Another major aim for us is to lower the MCU power consumption to fulfill the requirement of the embedded platform. Megawin Technology has branded itself with the motto "be practical and be creative." In order to become a qualified worldwide MCU supplier, we would keep developing innovative products constantly and continuously. Company OverviewMegawin Technology Co., Ltd4Product CategoryMEGAWINProduct 8051 MCUARM Cotrex-MUSB MCU6502 MCUMG82FG5 SeriesMG82G5 SeriesMG32F02A SeriesMG87 SeriesMPC89 SeriesMG84 SeriesMG74 Series ( OTP )MPC82 SeriesMG82F SeriesMG86 Series ( MTP )MG69 SeriesMG69L9 SeriesMG65 SeriesMG64 SeriesMLC SeriesMA1x SeriesLED DriverPower ManagementMG26 SeriesMG65 SeriesMG69 SeriesMG39/MG29 Serie

Service Details:

Operating Conditions • 3.0V to 3.6V, -40ºC to +125ºC, DC to 60 MIPS • 3.0V to 3.6V, -40ºC to +85ºC, DC to 70 MIPS Core: 16-Bit dsPIC33E/PIC24E CPU • Code-Efficient (C and Assembly) architecture • Two 40-Bit Wide Accumulators • Single-Cycle (MAC/MPY) with Dual Data Fetch • Single-Cycle Mixed-Sign MUL Plus Hardware Divide • 32-Bit Multiply Support Clock Management • 2% Internal Oscillator • Programmable PLLs and Oscillator Clock Sources • Fail-Safe Clock Monitor (FSCM) • Independent Watchdog Timer • Fast Wake-up and Start-up Power Management • Low-Power Management modes (Sleep, Idle, Doze) • Integrated Power-on Reset and Brown-out Reset • 1.0 mA/MHz Dynamic Current (typical) •60 µA IPD Current (typical) High-Speed PWM • Up to Seven PWM Pairs with Independent Timing • Dead Time for Rising and Falling Edges • 8.32 ns PWM Resolution • PWM Support for:- DC/DC, AC/DC, Inverters, PFC, Lighting- BLDC, PMSM, ACIM, SRM • Programmable Fault Inputs • Flexible Trigger Configurations for ADC Conversions Advanced Analog Features • Two Independent ADC modules:- One ADC configurable as 10-bit, 1.1 Msps with four S&H or 12-bit, 500 ksps with one S&H- One 10-bit ADC, 1.1 Msps with four S&H- Eight S&H using both ADC 10-bit modules- 24 analog channels (64-pin devices) up to 32 analog channels (100/121/144-pin devices) • Flexible and Independent ADC Trigger Sources • Comparators:- Up to three Analog Comparator modules- Programmable references with 32 voltage points Timers/Output Compare/Input Capture • 27 General Purpose Timers:- Nine 16-bit and up to four 32-bit Timers/Counters- 16 OC modules configurable as Timers/Counters- Two 32-bit Quadrature Encoder Interface (QEI) modules configurable as Timers/Counters • 16 IC modules • Peripheral Pin Select (PPS) to allow Function Remap • Real-Time Clock and Calendar (RTCC) module Communication Interfaces • USB 2.0 OTG-Compliant Full-Speed Interface • Four UART modules (15 Mbps)- Supports LIN/J2602 protocols and IrDA® • Four 4-Wire SPI modules (15 Mbps) • Two ECAN™ modules (1 Mbaud) CAN 2.0B Support •Two I2C modules (up to 1 Mbaud) with SMBus Support • Data Converter Interface (DCI) module with Support for I2S and Audio Codecs • PPS to allow Function Remap • Parallel Master Port (PMP) • Programmable Cyclic Redundancy Check (CRC) Direct Memory Access (DMA) • 15-Channel DMA with User-Selectable Priority Arbitration • UART, USB, SPI, ADC, ECAN™, IC, OC, Timers, DCI/I2S, PMP Input/Output • Sink/Source 10 mA on All Pins • 5V Tolerant Pins • Selectable Open-Drain, Pull-ups and Pull-Downs • Up to 5 mA Overvoltage Clamp Current • External Interrupts on All I/O pins Qualification and Class B Support

Service Details:

Features • Incorporates the ARM7TDMI® ARM® Thumb® Processor – High-performance 32-bit RISC Architecture – High-density 16-bit Instruction Set – Leader in MIPS/Watt – EmbeddedICE™ In-circuit Emulation, Debug Communication Channel Support • Internal High-speed Flash – 512 Kbytes, Organized in Two Contiguous Banks of 1024 Pages of 256 Bytes Dual Plane (SAM7SE512) – 256 Kbytes (SAM7SE256) Organized in One Bank of 1024 Pages of 256 Bytes Single Plane (SAM7SE256) – 32 Kbytes (SAM7SE32) Organized in One Bank of 256 Pages of 128 Bytes Single Plane (SAM7SE32) – Single Cycle Access at Up to 30 MHz in Worst Case Conditions – Prefetch Buffer Optimizing Thumb Instruction Execution at Maximum Speed – Page Programming Time: 6 ms, Including Page Auto-erase, Full Erase Time: 15 ms – 10,000 Erase Cycles, 10-year Data Retention Capability, Sector Lock Capabilities, Flash Security Bit – Fast Flash Programming Interface for High Volume Production • 32 Kbytes (SAM7SE512/256) or 8 Kbytes (SAM7SE32) of Internal High-speed SRAM, Single-cycle Access at Maximum Speed • One External Bus Interface (EBI) – Supports SDRAM, Static Memory, Glueless Connection to CompactFlash® and ECC-enabled NAND Flash • Memory Controller (MC) – Embedded Flash Controller – Memory Protection Unit – Abort Status and Misalignment Detection • Reset Controller (RSTC) – Based on Power-on Reset Cells and Low-power Factory-calibrated Brownout Detector – Provides External Reset Signal Shaping and Reset Source Status • Clock Generator (CKGR) – Low-power RC Oscillator, 3 to 20 MHz On-chip Oscillator and One PLL • Power Management Controller (PMC) – Power Optimization Capabilities, Including Slow Clock Mode (Down to 500 Hz) and Idle Mode – Three Programmable External Clock Signals • Advanced Interrupt Controller (AIC) – Individually Maskable, Eight-level Priority, Vectored Interrupt Sources – Two External Interrupt Sources and One Fast Interrupt Source, Spurious Interrupt Protected • Debug Unit (DBGU) – Two-wire UART and Support for Debug Communication Channel interrupt, Programmable ICE Access Prevention – Mode for General Purpose Two-wire UART Serial Communication • Periodic Interval Timer (PIT) – 20-bit Programmable Counter plus 12-bit Interval Counter • Windowed Watchdog (WDT) – 12-bit key-protected Programmable Counter AT91SAM ARM-based Flash MCU SAM7SE512 SAM7SE256 SAM7SE32 6222H–ATARM–25-Jan-12 2 6222H–ATARM–25-Jan-12 SAM7SE512/256/32 – Provides Reset or Interrupt Signals to the System – Counter May Be Stopped While the Processor is in Debug State or in Idle Mode • Real-time Timer (RTT) – 32-bit Free-running Counter with Alarm – Runs Off the Internal RC Oscillator • Three Parallel Input/Output Controllers (PIO) – Eighty-eight Programmable I/O Lines Multiplexed with up to Two Peripheral I/Os – Input Change Interrupt Capability on Each I/O Line – Individually Programmable Open-drain, Pull-up Resistor and Synchronous Output – Schmitt Trigger on All inputs • Eleven Peripheral DMA Controller (PDC) Channels • One USB 2.0 Full Speed (12 Mbits per second) Device Port – On-chip Transceiver, Eight Endpoints, 2688- 

Service Details:

Extreme Low-Power Features: • Multiple Power Management Options for Extreme Power Reduction: - VBAT allows the device to transition to a backup battery for the lowest power consumption with RTCC - Deep Sleep allows near total power-down with the ability to wake-up on external triggers - Sleep and Idle modes selectively shut down peripherals and/or core for substantial power reduction and fast wake-up - Doze mode allows CPU to run at a lower clock speed than peripherals • Alternate Clock modes Allow On-the-Fly Switching to a Lower Clock Speed for Selective Power Reduction • Extreme Low-Power Current Consumption for Deep Sleep: - WDT: 270 nA @ 3.3V typical - RTCC: 400 nA @ 32 kHz, 3.3V typical - Deep Sleep current, 40 na, 3.3V typical Peripheral Features: • LCD Display Controller: - Up to 60 segments by 8 commons - Internal charge pump and low-power, internal resistor biasing - Operation in Sleep mode • Up to Five External Interrupt Sources • Peripheral Pin Select (PPS): Allows Independent I/O Mapping of Many Peripherals • Five 16-Bit Timers/Counters with Prescaler: - Can be paired as 32-bit timers/counters • Six-Channel DMA supports All Peripheral modules: - Minimizes CPU overhead and increases data throughput Peripheral Features (Continued): • Seven Input Capture modules, each with a Dedicated 16-Bit Timer • Seven Output Compare/PWM modules, each with a Dedicated 16-Bit Timer • Enhanced Parallel Master/Slave Port (EPMP/EPSP) • Hardware Real-Time Clock/Calendar (RTCC): - Runs in Deep Sleep and VBAT modes • Two 3-Wire/4-Wire SPI modules (support 4 Frame modes) with 8-Level FIFO Buffer • Two I2C™ modules Support Multi-Master/Slave mode and 7-Bit/10-Bit Addressing • Four UART modules: - Support RS-485, RS-232 and LIN/J2602 - On-chip hardware encoder/decoder for IrDA® - Auto-wake-up on Auto-Baud Detect - 4-level deep FIFO buffer • Programmable 32-Bit Cyclic Redundancy Check (CRC) Generator • Digital Signal Modulator Provides On-Chip FSK and PSK Modulation for a Digital Signal Stream • Configurable Open-Drain Outputs on Digital I/O Pins • High-Current Sink/Source (18 mA/18 mA) on All I/O Pins Analog Features: • 10/12-Bit, 24-Channel Analog-to-Digital (A/D) Converter: - Conversion rate of 500 ksps (10-bit), 200 ksps (12-bit) - Conversion available during Sleep and Idle • Three Rail-to-Rail Enhanced Analog Comparators with Programmable Input/Output Configuration • On-Chip Programmable Voltage Reference • Charge Time Measurement Unit (CTMU): - Used for capacitive touch sensing, up to 24 channels - Time measurement down to 1 ns resolution - CTMU temperature sensing Device Pins Memory Remappable Peripherals I 2C™ 10/12-Bit ADC (ch) Comparators CTMU (ch) EPMP/EPSP LCD (pixels) JTAG Deep Sleep w/VBAT Flash Program (bytes) Data SRAM (bytes) 16-Bit Timers Capture Input Compare/PWM Output UART w/IrDA® SPI PIC24FJ128GA310 100 128K 8K 5 7 7 4 2 2 24 3 24 Y 480 Y Y PIC24FJ128GA308 80 128K 8K 5 7 7 4 2 2 16 3 16 Y 368 Y Y PIC24FJ128GA306 64 128K 8K 5 7 7 4 2 2 16 3 16 Y 240 Y Y PIC24FJ64GA310 100 64K 8K 5 7 7 4 2 2 24 3 24 Y 480 Y Y PIC24FJ64GA308 80 64K 8K 5 7 7 4 2 2 16 3 16 Y 368 Y Y PIC24FJ64GA306 64 64K 8K 5 7 7 4 2 2 16 3 16 Y 240 Y Y

Service Details:

Features Universal Serial Bus (USB) • Supports Full-Speed USB (12 Mb/s) • Implements USB Protocol Composite Device: - Communication Device Class (CDC) for Communications and Configuration - Human Interface Device (HID) for I/O control • 128-Byte Buffer to Handle Data Throughput at Any UART Baud Rate: - 64-byte transmit - 64-byte receive • Fully Configurable VID and PID Assignments and String Descriptors • Bus-Powered or Self-Powered • USB 2.0 Compliant: TID 40001150 USB Driver and Software Support • Uses Standard Windows® Drivers for Virtual Com Port (VCP): Windows XP (SP2 or later), Windows Vista, Windows 7, Windows 8, Windows 8.1 and Windows 10 • Configuration Utility for Initial Configuration Universal Asynchronous Receiver/Transmitter (UART) • Responds to SET_LINE_CODING Commands to Dynamically Change Baud Rates • Supports Baud Rates: 300-1000k • Hardware Flow Control • UART Signal Polarity Option General Purpose Input/Output (GPIO) Pins • Eight General Purpose I/O pins EEPROM • 256 Bytes of User EEPROM Other • USB Activity LED Outputs (TxLED and RxLED) • SSPND Output Pin • USBCFG Output Pin (indicates when the enumeration is completed) • Operating Voltage: 3.0V-5.5V • Oscillator Input: 12 MHz • Electrostatic Discharge (ESD) Protection: >4 kV Human Body Model (HBM) • Industrial (I) Operating Temperature: –40°C to +85°C • Passes Automotive AEC-Q100 Reliability Testing Package Types The device is offered in the following packages: • 20-lead VQFN (5x5 mm) • 20-lead SOIC • 20-lead SSOP 2 MCP2200 SOIC, SSOP OSC2 OSC1 RST 1 2 3 4 20 19 18 17 VDD VSS D+ DVusb GP7/TxLED 5 16 GP0/SSPND GP6/RxLED 6 15 GP5 7 14 GP2 GP1/USBCFG MCP2200 5x5 VQFN* GP6/RxLED GP5 RST DVusb G P3 GP0/SSPND Tx R T S Rx GP1/USBCFG O S C2 O S C1 VDD VSS GP7/TxLED EP 20 1 19 18 17 3 4 15 14 13 12 6 7 8 9 21 13 12 11 CTS Rx RTS GP4 8 GP3 9 Tx 10 D+ 16 GP4 5 11 GP2 C T S 10 * Includes Exposed Thermal Pad (EP); see Table 1-1. USB 2.0 to UART Protocol Converter with GPIO MCP2200 DS20002228E-page 2 ??? 2010-2021 Microchip Technology Inc. Block Diagram UART Controller USB Protocol Controller USB Transceiver 3.3V LDO Configuration & Control Registers OSC Reset Control USB Clock State Clock GPIO Baud Generator VSS VUSB RST VSS VDD Rx Tx CTS RTS D+ DOSC1 OSC2 USB LEDs GP0 TxLED Rx

Service Details:

Features Universal Serial Bus (USB) • Supports Full-Speed USB (12 Mb/s) • Implements USB Protocol Composite Device: - Communication Device Class (CDC) for Communications and Configuration - Human Interface Device (HID) for I/O control • 128-Byte Buffer to Handle Data Throughput at Any UART Baud Rate: - 64-byte transmit - 64-byte receive • Fully Configurable VID and PID Assignments and String Descriptors • Bus-Powered or Self-Powered • USB 2.0 Compliant: TID 40001150 USB Driver and Software Support • Uses Standard Windows® Drivers for Virtual Com Port (VCP): Windows XP (SP2 or later), Windows Vista, Windows 7, Windows 8, Windows 8.1 and Windows 10 • Configuration Utility for Initial Configuration Universal Asynchronous Receiver/Transmitter (UART) • Responds to SET_LINE_CODING Commands to Dynamically Change Baud Rates • Supports Baud Rates: 300-1000k • Hardware Flow Control • UART Signal Polarity Option General Purpose Input/Output (GPIO) Pins • Eight General Purpose I/O pins EEPROM • 256 Bytes of User EEPROM Other • USB Activity LED Outputs (TxLED and RxLED) • SSPND Output Pin • USBCFG Output Pin (indicates when the enumeration is completed) • Operating Voltage: 3.0V-5.5V • Oscillator Input: 12 MHz • Electrostatic Discharge (ESD) Protection: >4 kV Human Body Model (HBM) • Industrial (I) Operating Temperature: –40°C to +85°C • Passes Automotive AEC-Q100 Reliability Testing Package Types The device is offered in the following packages: • 20-lead VQFN (5x5 mm) • 20-lead SOIC • 20-lead SSOP 2 MCP2200 SOIC, SSOP OSC2 OSC1 RST 1 2 3 4 20 19 18 17 VDD VSS D+ DVusb GP7/TxLED 5 16 GP0/SSPND GP6/RxLED 6 15 GP5 7 14 GP2 GP1/USBCFG MCP2200 5x5 VQFN* GP6/RxLED GP5 RST DV

Service Details:

Features:

• High Performance, Low Power Atmel® AVR® 8-Bit Microcontroller 
• Advanced RISC Architecture 
• 135 Powerful Instructions 
• Most Single Clock Cycle Execution 
• 32 × 8 General Purpose Working Registers 
• Fully Static Operation 
• Up to 16 MIPS Throughput at 16MHz 
• On-Chip 2-cycle Multiplier 
• High Endurance Non-volatile Memory Segments 
• 64K/128K/256KBytes of In-System Self-Programmable Flash 
• 4Kbytes EEPROM 
• 8Kbytes Internal SRAM 
• Write/Erase Cycles:10,000 Flash/100,000 EEPROM 

Data retention: 

• 20 years at 85 Deg C/ 100 years at 25 Deg C 
• Optional Boot Code Section with Independent Lock Bits 
• In-System Programming by On-chip Boot Program 
• True Read-While-Write Operation 
• Programming Lock for Software Security 

Endurance: 

• Up to 64Kbytes Optional External Memory Space 
• Atmel® QTouch® library support 
• Capacitive touch buttons, sliders and wheels 
• QTouch and QMatrix acquisition – Up to 64 sense channels 
• JTAG (IEEE® std. 1149.1 compliant) Interface 
• Boundary-scan Capabilities According to the JTAG Standard 
• Extensive On-chip Debug Support 
• Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface 

Peripheral Features:

• Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode 
• Four 16-bit Timer/Counter with Separate Prescaler, Compare- and Capture Mode 
• Real Time Counter with Separate Oscillator 
• Four 8-bit PWM Channels 
• Six/Twelve PWM Channels with Programmable Resolution from 2 to 16 Bits (ATmega1281/2561, ATmega640/1280/2560) 
• Output Compare Modulator 
• 8/16-channel, 10-bit ADC (ATmega1281/2561, ATmega640/1280/2560) 
• Two/Four Programmable Serial USART (ATmega1281/2561, ATmega640/1280/2560) 
• Master/Slave SPI Serial Interface – Byte Oriented 2-wire Serial Interface 
• Programmable Watchdog Timer with Separate On-chip Oscillator 
• On-chip Analog Comparator 
• Interrupt and Wake-up on Pin Change 

Special Microcontroller Features:

• Power-on Reset and Programmable Brown-out Detection
• Internal Calibrated Oscillator 
• External and Internal Interrupt Sources 
• Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby 
• I/O and Packages – 54/86 Programmable I/O Lines (ATmega1281/2561, ATmega640/1280/2560) – 64-pad QFN/MLF, 64-lead TQFP (ATmega1281/2561) 
• 100-lead TQFP, 100-ball CBGA (ATmega640/1280/2560) – RoHS/Fully Green 
• Ultra-Low Power Consumption – Active Mode: 1MHz, 1.8V: 500µA – Power-down Mode: 0.1µA at 1.8V 

Speed Grade: 

• ATmega640V/ATmega1280V/ATmega1281V
• 0 - 4MHz @ 1.8V - 5.5V, 0 - 8MHz @ 2.7V - 5.5V – ATmega 2560V/ATmega2561V
• 0 - 2MHz @ 1.8V - 5.5V, 0 - 8MHz @ 2.7V - 5.5V – ATmega640/ATmega1280/ATmega1281
• 0 - 8MHz @ 2.7V - 5.5V, 0 - 16MHz @ 4.5V

Service Details:

16-bit Microcontrollers - MCU 16B 16MIPS 256KB I/O RAM52 OTGThis document contains device-specific information for the following devices: This expands on the existing line of Microchip‘s 16-bit microcontrollers, combining an expanded peripheral feature set and enhanced computational performance with a new connectivity option: USB On-The-Go. The PIC24FJ256GB110 family provides a new platform for high-performance USB applications, which may need more than an 8-bit platform, but don’t require the power of a digital signal processor. 1.1 Core Features 1.1.1 16-BIT ARCHITECTURE Central to all PIC24F devices is the 16-bit modified Harvard architecture, first introduced with Microchip’s dsPIC® digital signal controllers. The PIC24F CPU core offers a wide range of enhancements, such as: • 16-bit data and 24-bit address paths with the ability to move information between data and memory spaces • Linear addressing of up to 12 Mbytes (program space) and 64 Kbytes (data) • A 16-element working register array with built-in software stack support • A 17 x 17 hardware multiplier with support for integer math • Hardware support for 32 by 16-bit division • An instruction set that supports multiple addressing modes and is optimized for high-level languages such as ‘C’ • Operational performance up to 16 MIPS 1.1.2 POWER-SAVING TECHNOLOGY All of the devices in the PIC24FJ256GB110 family incorporate a range of feature peripherals, allowing for a smooth migration path as applications grow and evolve. The consistent pinout scheme used throughout the entire family also aids in migrating from one device to the next larger, or even in jumping from 64-pin to 100-pin devices. The PIC24F family is pin-compatible with devices in the dsPIC33 family, and shares some compatibility with the pinout schema for PIC18 and dsPIC30. This extends the ability of applications to grow from the relatively simple, to the powerful and complex, yet still selecting a Microchip device. • PIC24FJ64GB106 • PIC24FJ192GB108 • PIC24FJ128GB106 • PIC24FJ256GB108 • PIC24FJ192GB106 • PIC24FJ64GB110 • PIC24FJ256GB106 • PIC24FJ128GB110 • PIC24FJ64GB108 • PIC24FJ192GB110 • PIC24FJ128GB108 • PIC24FJ256GB110

Service Details:

 ATMEL Microcontroller ATMEGA16A-PU, ATMEL Microcontroller ATMEGA128A-AU, ATMEL Microcontroller ATMEGA2560-16AU, ATMEL MICROCONTROLLER AT89C2051-24PU, PIC18F4520-I/P and PIC18F252-I/SP

Additional Information:

• Packaging Details: ESD

Service Details:

AT89C2051-24PU
Microchip TechnologyIC MCU 8BIT 2KB FLASH 20DIP

Additional Information:

• Delivery Time: 2
• Packaging Details: esd