TEXAS INSTRUMENT IC

Service Details:

Features 1• Stable With 1-μF or Larger Ceramic Output Capacitor • Input Voltage Range: 2.2 V to 5.5 V • Ultralow Dropout Voltage: 130 mV Typical at 1 A • Excellent Load Transient Response—Even With Only 1-μF Output Capacitor • NMOS Topology Delivers Low Reverse Leakage Current • 1% Initial Accuracy • 3% Overall Accuracy Over Line, Load, and Temperature • Less Than 20 nA Typical IQ in Shutdown Mode • Thermal Shutdown and Current Limit for Fault Protection • Available in Multiple Output Voltage Versions – Adjustable Output: 1.20 V to 5.5 V – Custom Outputs Available Using Factory Package-Level Programming 2 Applications • Point-of-Load Regulation for DSPs, FPGAs, ASICs, and Microprocessors • Post-Regulation for Switching Supplies • Portable and Battery-Powered Equipment space 3 Description The TPS737xx family of linear low-dropout (LDO) voltage regulators uses an NMOS pass element in a voltage-follower configuration. This topology is relatively insensitive to output capacitor value and ESR, allowing a wide variety of load configurations. Load transient response is excellent, even with a small 1-μF ceramic output capacitor. The NMOS topology also allows very low dropout. The TPS737xx family uses an advanced BiCMOS process to yield high precision while delivering very low dropout voltages and low ground pin current. Current consumption, when not enabled, is less than 20 nA and ideal for portable applications. These devices are protected by thermal shutdown and foldback current limit. For applications that require higher output voltage accuracy, consider TI's TPS7A37xx family of 1% overall accuracy, 1-A low-dropout voltage regulators. Device Information(1) PART NUMBER PACKAGE BODY SIZE (NOM) TPS737xx VSON (8) 3.00 mm × 3.00 mm

Service Details:

LDO Voltage Regulators 2-A, low-noise, high-PSRR, adjustable ultra-low-dropout voltage regulator with high-accuracy 10-SON -40 to 125

Service Details:

Device Overview 1.1 Features 1 • Upto 1-GHz Sitara™ ARM® Cortex®-A8 32 Bit RISC Processor– NEON™SIMDCoprocessor– 32KB of L1 Instruction and 32KB of Data Cache With Single-Error Detection (Parity)– 256KB of L2 Cache With Error Correcting Code (ECC)– 176KB of On-Chip Boot ROM– 64KB of Dedicated RAM– Emulation and Debug- JTAG– Interrupt Controller (up to 128 Interrupt Requests) • On-Chip Memory (Shared L3 RAM)– 64KB of General-Purpose On-Chip Memory Controller (OCMC) RAM– Accessible to All Masters– Supports Retention for Fast Wakeup • External Memory Interfaces (EMIF)– mDDR(LPDDR), DDR2, DDR3, DDR3L Controller:– mDDR: 200-MHz Clock (400-MHz Data Rate)– DDR2: 266-MHz Clock (532-MHz Data Rate)– DDR3: 400-MHz Clock (800-MHz Data Rate)– DDR3L: 400-MHz Clock (800-MHz Data Rate)– 16-Bit Data Bus– 1GBof Total Addressable Space– Supports One x16 or Two x8 Memory Device Configurations– General-Purpose Memory Controller (GPMC)– Flexible 8-Bit and 16-Bit Asynchronous Memory Interface With up to Seven Chip Selects (NAND, NOR, Muxed-NOR, SRAM)– Uses BCH Code to Support 4-, 8-, or 16-Bit ECC– Uses Hamming Code to Support 1-Bit ECC– Error Locator Module (ELM)– Used in Conjunction With the GPMC to Locate Addresses of Data Errors from Syndrome Polynomials Generated Using a BCH Algorithm– Supports 4-, 8-, and 16-Bit per 512-Byte Block Error Location Based on BCH Algorithms • Programmable Real-Time Unit Subsystem and Industrial Communication Subsystem (PRU-ICSS)– Supports Protocols such as EtherCAT®, 1 PROFIBUS, PROFINET, EtherNet/IP™, and More– TwoProgrammable Real-Time Units (PRUs)– 32-Bit Load/Store RISC Processor Capable of Running at 200 MHz– 8KBof Instruction RAM With Single-Error Detection (Parity)– 8KBof Data RAM With Single-Error Detection (Parity)– Single-AM3359ZCZ AM3358ZCZ AM3357ZCZ AM3356ZCZ, AM3356ZCE AM3354ZCZ, AM3354ZCE AM3352ZCZ, AM3352ZCE AM3351ZCE NFBGA (324) NFBGA (324) NFBGA (324) BODY SIZE NFBGA (324), NFBGA (298) 15.0 mm × 15.0 mm 15.0 mm × 15.0 mm 15.0 mm × 15.0 mm 15.0 mm × 15.0 mm, 13.0 mm × 13.0 mm NFBGA (324), NFBGA (298) NFBGA (324), NFBGA (298) NFBGA (298) (1) For more information, see Section 9, Mechanical, Packaging, and Orderable Information. 15.0 mm × 15.0 mm, 13.0 mm × 13.0 mm 15.0 mm × 15.0 mm, 13.0 mm × 13.0 mm 13.0 mm × 13.0 mm
AM3351BZCE30ACTIVENFBGAZCE298160RoHS & GreenSNAGCULevel-3-260C-168 HR0 to 90AM3351BZCE30 AM3351BZCE30RACTIVENFBGAZCE2981000RoHS & GreenSNAGCULevel-3-260C-168 HR0 to 90AM3351BZCE30 AM3351BZCE60ACTIVENFBGAZCE298160RoHS & GreenSNAGCULevel-3-260C-168 HR0 to 90AM3351BZCE60 AM3351BZCE60RACTIVENFBGAZCE2981000RoHS & GreenSNAGCULevel-3-260C-168 HR0 to 90AM3351BZCE60 AM3351BZCEA30ACTIVENFBGAZCE298160RoHS & GreenSNAGCULevel-3-260C-168 HR-40 to 105AM3351BZCEA30 AM3351BZCEA30RACTIVENFBGAZCE2981000RoHS & GreenSNAGCULevel-3-260C-168 HR-40 to 105AM3351BZCEA30 AM3351BZCEA60ACTIVENFBGAZCE298160RoHS & GreenSNAGCULevel-3-260C-168 HR-40 to 105AM3351BZCEA60 AM3352BZCE30ACTIVENFBGAZCE298160RoHS & GreenCall TILevel-3-260C-168 HR0 to 90AM3352BZCE30 AM3352BZCE30RACTIVENFBGAZCE2981000RoHS & GreenSNAGCULevel-3-260C-168 HRAM3352BZCE30 AM3352BZCE60ACTIVENFBGAZCE298160RoHS & GreenSNAGCULevel-3-260C-168 HR0 to 90AM3352BZCE60 AM3352BZCEA30ACTIVENFBGAZCE298160RoHS & GreenSNAGCULevel-3-260C-168 HR-40 to 105AM3352BZCEA30 AM3352BZCEA30RACTIVENFBGAZCE2981000RoHS & GreenCall TILevel-3-260C-168 HR-40 to 105AM3352BZCEA30 AM3352BZCEA60ACTIVENFBGAZCE298160RoHS & GreenSNAGCULevel-3-260C-168 HR-40 to 105AM3352BZCEA60 AM3352BZCEA60RACTIVENFBGAZCE2981000RoHS & GreenCall TILevel-3-260C-168 HR-40 to 105AM3352BZCEA60

Service Details:

DP83867E/IS/CS Robust, High Immunity, Small Form Factor 10/100/1000 Ethernet Physical Layer Transceiver 1 Features 1 • Extra low latency TX < 90 ns, RX < 290 ns • Time Sensitive Network (TSN) compliant • Lowpower consumption: 457 mW • Exceeds 8000 V IEC 61000-4-2 ESD protection • Meets EN55011 class B emission standards • 16programmable RGMII delay modes on RX/TX • Integrated MDI termination resistors • Programmable MAC interface termination impedance • WoL(Wake-on-LAN) packet detection • 25-MHz or 125-MHz synchronized clock output • IEEE1588 time stamp support • RJ45mirror mode • Fully compatible to IEEE 802.3 10BASE-Te, 100BASE-TX, and 1000BASE-T Specification • Cable diagnostics • RGMII and SGMII MAC interface options • Configurable I/O voltage (3.3 V, 2.5 V, 1.8 V) • Fast link drop mode • JTAGsupport 2 Applications • Motor drives • Industrial factory automation • Field Bus Support • Industrial embedded computing • Wired and wireless communications infrastructure • Test and measurement • Consumer electronics Ethernet MAC 1 RGMII SGMII 3 Description The DP83867 device is a robust, low power, fully featured Physical Layer transceiver with integrated PMD sublayers to support 10BASE-Te, 100BASE-TX and 1000BASE-T Ethernet protocols. Optimized for ESD protection, the DP83867 exceeds 8-kV IEC 61000-4-2 (direct contact). The DP83867 is designed for easy implementation of 10/100/1000 Mbps Ethernet LANs. It interfaces directly to twisted pair media through an external transformer. This device interfaces directly to the MAC layer through Reduced GMII (RGMII) or embedded clock Serial GMII (SGMII). The DP83867 provides precision clock synchronization, including a synchronous Ethernet clock output. It has low latency and provides IEEE 1588 Start of Frame Detection. Designed for low power, the DP83867 consumes only 457 mW under full operating power. Wake-on-LAN can be used to lower system power consumption. Device Information(1) PART NUMBER TEMPERATURE PACKAGE BODYSIZE(NOM) DP83867CSRGZ DP83867ISRGZ DP83867ERGZ 0°C to +70°C VQFN (48) 7mm×7mm–40°C to +85°C VQFN (48) 7 mm×7mm–40°C to +105°C VQFN (48) 7 mm× 7 mm (1) For all available packages, see the orderable addendum at
DP83867CS DP83867IS DP83867E

Service Details:

TPS27081A 1.2-V to 8-V, 3-A PFET High-Side Load Switch With Level Shift and Adjustable Slew Rate Control 1 Features • LowON-Resistance, High-Current PFET 1– RDS(on) = 32 m??? at VGS =–4.5 V– RDS(on) = 44 m??? at VGS =–3 V– RDS(on) = 82 m??? at VGS =–1.8 V– RDS(on) = 93 m??? at VGS =–1.5 V– RDS(on) = 155 m??? at VGS =–1.2 V • Adjustable Turnon and Turnoff Slew Rate Control Through External R1, R2, and C1 • Supports a Wide Range of 1.2-V to 8-V Supply Inputs • Integrated NMOS for PFET Control • NMOSON/OFFSupports a Wide Range of 1-V to 8-V Control Logic Interface • Full ESD Protection (All Pins)– HBM2kV,CDM500V • Ultra-Low Leakage Current in Standby (Typical 100 nA) • Available in Tiny 6-Pin Package– 2.9 mm×2.8 mm×0.75 mmSOT(DDC) 2 Applications • High-Side Load Switches • Inrush Current Control • Power Sequencing and Control • Standby Power Isolation • Portable Power Switches Up to 8V Supply VIN R1 (4) 3 Description The TPS27081A device is a high-side load switch that integrates a Power PFET and a Control NFET in a tiny package. The TPS27081A features industry-standard ESD protection on all pins providing better ESD compatibility with other onboard components. The TPS27081A level shifts ON/OFF logic signal to VIN levels and supports as low as 1-V CPU or MCU logic to control higher voltage power supplies without requiring an external level-shifter. Switching a large value output capacitor CL through a fast ON/OFF logic signal may result in an excessive inrush current. To control the load inrush current, connect a resistor R2 and add an external capacitor C1 as shown in the Simplified Schematic. To configure the TPS27081A to achieve a specific slew rate, refer to the Application and Implementation section. A single pullup resistor R1 is required in standby power switch applications. In such applications connect the R2 pin of the TPS27081A to the system ground when inrush current control is not required. Device Information(1) PART NUMBER PACKAGE TPS27081A SOT (6) BODY SIZE (NOM) 2.90 mm × 1.60 mm (1) For all available packages, see the orderable addendum at the end of the data s

Service Details:

Features 1 • Qualified for Automotive Applications • AEC-Q100 Test Guidance With the Following:– Device Temperature Grade 1– Device Temperature Grade 0 (TPS7A6650EDGNRQ1 Only)– Device HBM ESD Classification Level H2– Device CDM ESD Classification Level C4 • Device Junction Temperature Range:–40°C to +150°C • 4-Vto 40-V Wide Vin Input Voltage Range With up to 45-V Transient • Output Current: 150 mA • LowQuiescent Current, I(q):– 2µAWhenEN=Low(Shutdown Mode)– 12µATypical at Light Loads • LowESRCeramic Output Stability Capacitor (2.2 µF–100 µF) • 300-mV Dropout Voltage at 150 mA (Typical, V(Vin) = 4 V) • Fixed (3.3-V and 5-V) and Adjustable (1.5-V to 5-V) Output Voltages (Adjustable for TPS7A66-Q1 Only) • LowInput Voltage Tracking • Integrated Power-On Reset:– Programmable Reset-Pulse Delay– Open-Drain Reset Output • Integrated Fault Protection:– Thermal Shutdown– Short-Circuit Protection • Input Voltage Sense Comparator (TPS7A69-Q1 Only) • Packages:– 8-Pin SOIC-D for TPS7A69-Q1– 8-Pin HVSSOP-DGN for TPS7A6601-Q1 Hardware-Enable Option TPS7A66-Q1 V(bat) 1 2 Vin EN CT Vout PG 45 GND 1 Copyright © 2017, Texas Instruments Incorporated 2 Applications • Infotainment Systems With Sleep Mode • BodyControl Modules • Always-On Battery Applications:– Gateway Applications– Remote Keyless Entry Systems– Immobilizers 3 Description The TPS7A66-Q1 and TPS7A69-Q1 are low-dropout linear regulators designed for up to 40-V Vin operations. With only 12-µA quiescent current at no load, they are quite suitable for standby microprocessor control-unit systems, especially in automotive applications. The devices feature integrated short-circuit and overcurrent protection. The devices implement reset delay on power up to indicate the output voltage is stable and in regulation. One can program the delay with an external capacitor. A low-voltage tracking feature allows for a smaller input capacitor and can possibly eliminate the need of using a boost converter during cold-crank conditions. The devices operate in the–40°C to 125°C temperature range. The TPS7A6650EDGNRQ1 device is qualified to AEC-Q100 grade 0, operating in the–40°C to 150°C temperature range. These features suit the devices well for power supplies in various automotive applications. Device Information(1) PART NUMBER PACKAGE TPS7A66-Q1 TPS7A69-Q1 HVSSOP (8) BODY SIZE (NOM) 3.00 mm × 3.00 mm SOIC (8) 4.90 mm × 3.91 mm (1) For all available packages, see the orderable addendum at the end of the data sheet.

Service Details:

LED Lighting Drivers high-accuracy LED controller with spread spectrum frequency modulation and internal PWM Generator 20-HTSSOP -40 to 125

Service Details:

Small-size VSSOP Packages Save Board Space, or SOIC for Drop-in Compatibility • Bus I/O Protection – >±15 kV HBM Protection – >±12 kV IEC 61000-4-2 Contact Discharge – >±4 kV IEC 61000-4-4 Fast Transient Burst • Extended Industrial Temperature Range –40°C to 125°C • Large Receiver Hysteresis (80 mV) for Noise Rejection • Low Unit-Loading Allows Over 200 Connected Nodes • Low Power Consumption – Low Standby Supply Current: < 2 µA – ICC < 1 mA Quiescent During Operation • 5-V Tolerant Logic Inputs Compatible With 3.3-V or 5-V Controllers • Signaling Rate Options Optimized for: 250 kbps, 20 Mbps, 50 Mbps • Glitch Free Power-Up and Power-Down

Service Details:

TMS320LF2407A,
TMS320LF2406A,
TMS320LF2403A,
TMS320LF2402ATMS320LC2406A,TMS320LC2404A,TMS320LC2403A,TMS320LC2402ADSP CONTROLLERSSPRS145L − JULY 2000 − REVISED SEPTEMBER 2007POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 1
High-Performance Static CMOS Technology− 25-ns Instruction Cycle Time (40 MHz)− 40-MIPS Performance− Low-Power 3.3-V Design
Based on TMS320C2xx DSP CPU Core− Code-Compatible With F243/F241/C242− Instruction Set and Module CompatibleWith F240
Flash (LF) and ROM (LC) Device Options− LF240xA: LF2407A, LF2406A,LF2403A, LF2402A− LC240xA: LC2406A, LC2404A,LC2403A, LC2402A
On-Chip Memory− Up to 32K Words x 16 Bits of FlashEEPROM (4 Sectors) or ROM− Programmable “Code-Security” Featurefor the On-Chip Flash/ROM− Up to 2.5K Words x 16 Bits ofData/Program RAM− 544 Words of Dual-Access RAM− Up to 2K Words of Single-Access RAM
Boot ROM (LF240xA Devices)− SCI/SPI Bootloader
Up to Two Event-Manager (EV) Modules(EVA and EVB), Each Includes:− Two 16-Bit General-Purpose Timers− Eight 16-Bit Pulse-Width Modulation(PWM) Channels Which Enable:− Three-Phase Inverter Control− Center- or Edge-Alignment of PWMChannels− Emergency PWM Channel ShutdownWith External PDPINTx Pin− Programmable Deadband (Deadtime)Prevents Shoot-Through Faults− Three Capture Units for Time-Stampingof External Events− Input Qualifier for Select Pins− On-Chip Position Encoder InterfaceCircuitry− Synchronized A-to-D Conversion− Designed for AC Induction, BLDC,Switched Reluctance, and Stepper MotorControl− Applicable for Multiple Motor and/orConverter Control
External Memory Interface (LF2407A)− 192K Words x 16 Bits of Total Memory:64K Program, 64K Data, 64K I/O
Watchdog (WD) Timer Module
10-Bit Analog-to-Digital Converter (ADC)− 8 or 16 Multiplexed Input Channels− 500-ns MIN Conversion Time− Selectable Twin 8-State SequencersTriggered by Two Event Managers
Controller Area Network (CAN) 2.0B Module(LF2407A, 2406A, 2403A)
Serial Communications Interface (SCI)
16-Bit Serial Peripheral Interface (SPI)(LF2407A, 2406A, LC2404A, 2403A)
Phase-Locked-Loop (PLL)-Based ClockGeneration
Up to 40 Individually Programmable,Multiplexed General-Purpose Input/Output(GPIO) Pins
Up to Five External Interrupts (Power DriveProtection, Reset, Two Maskable Interrupts)
Power Management:− Three Power-Down Modes− Ability to Power Down Each PeripheralIndependently
Real-Time JTAG-Compliant Scan-BasedEmulation, IEEE Standard 1149.1† (JTAG)
Development Tools Include:− Texas Instruments (TI) ANSI C Compiler,Assembler/Linker, and Code ComposerStudio??? Debugger− Evaluation Modules− Scan-Based Self-Emulation (XDS510???)− Broad Third-Party Digital Motor ControlSupport
Package Options− 144-Pin LQFP PGE (LF2407A)

Service Details:

1FEATURES DESCRIPTION The UC3625 family of motorcontroller devices • Drives Power MOSFETs or Power Darlingtons integrate most of the functions required for high- Directly performance brushless dc-motor control into one • 50-V Open Collector High-Side Drivers package. When coupled with external power • Latched Soft Start MOSFETs or Darlingtons, these devices perform fixed-frequency PWM motor control in either voltage • High-Speed Current-Sense Amplifier with Ideal or current mode while implementing closed-loop Diode speed control and braking with smart noise rejection, • Pulse-by-Pulse and Average Current Sensing safe direction reversal, and cross–conduction • Over-Voltage and Under-Voltage Protection protection. • Direction Latch for Safe Direction Reversal Although specified for operation from power supplies • Tachometer between 10 V and 18 V, the UC1625 controls higher voltage power devices with external level-shifting • Trimmed Reference Sources 30 mA components. The UC1625 contains fast, high-current • Programmable Cross-Conduction Protection push-pull drivers for low-side power devices and 50-V • Two-Quadrant and Four-Quadrant Operation open-collector outputs for high-side power devices or level-shifting circuitry. The UC1625 is characterized for operation over the military temperature range of –55°C to +125°C, while the UC2625 is characterized from –40°C to +105°C and the UC3625 is characterized from 0°C

Service Details:

Logic Gates Military 4-ch, 2-input, 4.5-V to 5.5-V bipolar NAND gates with Schmitt-Trigger inputs 14-CDIP -55 to 125
   

 

Service Details:

Inverters Military 6-ch, 4.5-V to 5.5-V bipolar inverters with Schmitt-Trigger inputs 14-CDIP -55 to 125
Features 1• Operation From Very Slow Edges • Improved Line-Receiving Characteristics • High Noise Immunity 2 Applications • HVAC Gateways • Residential Ductless Air Conditioning Outdoor Units • Robotic Controls • Industrial Stepper Motors • Power Meter and Power Analyzers • Digital Input Modules for Factory Automation

Each circuit in SNx414 and SNx4LS14 functions as an inverter. However, because of the Schmitt-Trigger action, they have different input threshold levels for positive-going (VT+) and negative-going (VT– ) signals. These circuits are temperature compensated and can be triggered from the slowest of input ramps and still give clean, jitter-free output signals. Device Information(1) PART NUMBER PACKAGE BODY SIZE (NOM) SN7414, SN74LS14 SOIC (14) 4.90 mm × 3.91 mm SSOP (14) 6.20 mm × 5.30 mm PDIP (14) 19.30 mm × 6.35 mm SO (14) 10.30 mm × 5.30 mm SN5414, SN54LS14 CDIP (14) 19.56 mm × 6.67 mm CFP (14) 9.21 mm × 5.97 mm LCCC (20) 8.89 mm × 8.89 mm

Service Details:

Counter Shift Registers Dual 4-Bit Binary Counters 14-CDIP -55 to 125Dual 4-Bit Binary Counters 14-CDIP -55 to 125INR 654.355Add to BOMDatasheet at TI.com6

Service Details:

Each of these monolithic counters contains four master-slave flip-flops and additional gating to provide a divide-by-two counter and a three-stage binary counter for which the count cycle length is divide-by-five for the '90A and 'LS90, divide-by-six for the '92A and 'LS92, and the divide-by eight for the '93A and 'LS93.

All of these counters have a gated zero reset and the '90A and 'LS90 also have gated set-to-nine inputs for use in BCD nine's complement applications.

To use their maximum count length (decade, divide-by-twelve, or four-bit binary) of these counters, the CKB input is connected to the QA output. The input count pulses are applied to CKA input and the outputs are as described in the appropriate function table. A symmetrical divide-by-ten count can be obtained from the '90A or 'LS90 counters by connecting the QD output to the CKA input and applying the input count to the CKB input which gives a divide-by-ten square wave at output QA.

Service Details:

Logic Gates AND-OR-invert Gates 14-CDIP -55 to 125

The '51 and 'S51 contain two independent 2-wide 2-input AND-OR-INVERT gates. They perform the Boolean function Y = AB + CD\.

The 'LS51 contains one 2-wide 3-input and one 2-wide 2-input AND-OR-INVERT gates. They perform the Boolean functions 1Y = (1A · 1B · 1C) + (1D · 1E · 1F)\ and 2Y = (2A · 2B) + (2C · 2D)\.

The SN5451, SN54LS51, and SN54S51 are characterized for operation over the full military temperature range of -55°C to 125°C. The SN7451, SN74LS51 and SN74S51 are characterized for operation from 0°C to 70°C.

Service Details:

Logic Gates Military 2-ch, 4-input, 4.5-V to 5.5-V bipolar NAND gates 14-CDIP -55 to 125Military 2-ch, 4-input, 4.5-V to 5.5-V bipolar NAND gates 14-CDIP -55 to 125
Description for the SN54LS20

These devices contain two independent 4-input NAND gates.

The SN5420, SN54LS20, and SN54S20 are characterized for operation over the full military range of -55°C to 125°C. The SN7420, SN74LS20, and SN74S20 are characterized for operation from 0°C to 70°C.

Service Details:

Dual J-K Flip-Flops With Clear and 3-state Outputs 14-CDIP -55 to 125

The '73, and 'H73, contain two independent J-K flip-flops with individual J-K, clock, and direct clear inputs. The '73, and 'H73, are positive pulse-triggered flip-flops. J-K input is loaded into the master while the clock is high and transferred to the slave on the high-to-low transition. For these devices the J and K inputs must be stable while the clock is high.

The 'LS73A contains two independent negative-edge-triggered flip-flops. The J and K inputs must be stable one setup time prior to the high-to-low clock transition for predictable operation. When the clear is low, it overrides the clock and data inputs forcing the Q output low and the Q\ output high.

The SN5473, SN54H73, and the SN54LS73A are characterized for operation over the full military temperature range of -55°C to 125°C. The SN7473, and the SN74LS73A are characterized for operation from 0°C to 70°C.

 

 

 

 

Service Details:

Translation - Voltage Levels CMOS Hex Voltage- Level Shifter
Download the free Library Loader to convert this file for your ECAD Tool. Learn more about the ECAD Model.

Service Details:

Digital Isolators Iso 5V Full & Half- Duplex RS-485 Xcvr1 Features 1• Meets or Exceeds TIA/EIA RS-485 Requirements • Signaling Rates up to 20 Mbps • 1/8 Unit Load – Up to 256 Nodes on a Bus • Thermal Shutdown Protection • Low Bus Capacitance – 16 pF (Typical) • 50 kV/μs Typical Transient Immunity • Fail-safe Receiver for Bus Open, Short, Idle • 3.3-V Inputs are 5-V Tolerant • Bus-Pin ESD Protection – 12-kV HBM Between Bus Pins and GND2 – 6-kV HBM Between Bus Pins and GND1 • Safety-Related Certifications: – 4000-VPK Basic Insulation, 560 VPK VIORM per DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12 and DIN EN 61010-1 – 2500 VRMS Isolation per UL 1577 – 4000 VPK Isolation per CSA Component Acceptance Notice 5A and IEC 60950-1 2 Applications • Security Systems • Chemical Production • Factory Automation • Motor and Motion Control • HVAC and Building Automation Networks • Networked Security Stations

Service Details:

DP83848C/I/VYB/YB PHYTER™ QFP Single Port 10/100 Mb/s Ethernet Physical Layer Transceiver
• Multiple Temperature Range from –40°C to 105°C • IEEE 802.3 ENDEC, 10BASE-T Transceivers and • Low-Power 3.3-V, 0.18-µm CMOS Technology Filters • Low-Power Consumption < 270 mW Typical • IEEE 802.3 PCS, 100BASE-TX Transceivers and Filters • 3.3-V MAC Interface • Auto-MDIX for 10/100 Mb/s • IEEE 1149.1 JTAG • Energy Detection Mode • Integrated ANSI X3.263 Compliant TP-PMD Physical Sub-Layer with Adaptive Equalization and • 25-MHz Clock Output Baseline Wander Compensation • SNI Interface (Configurable) • Error-Free Operation up to 150 Meters • RMII Rev. 1.2 Interface (Configurable) • Programmable LED Support for Link, 10/100 Mb/s • MII Serial Management Interface (MDC and MDIO) Mode, Activity, Duplex and Collision Detect • IEEE 802.3 MII • Single Register Access for Complete PHY Status • IEEE 802.3 Auto-Negotiation and Parallel • 10/100 Mb/s Packet BIST (Built in Self Test) Detection 1.2 Applications • Automotive/Transportation • General Embedded Applications • Industrial Controls and Factory Automation 1.3 Description The number of applications requiring Ethernet connectivity continues to increase, driving Ethernet enabled devices into harsher environments. The DP83848C/I/VYB/YB was designed to meet the challenge of these new applications with an extended temperature performance that goes beyond the typical Industrial temperature range. The DP83848C/I/VYB/YB is a highly reliable, feature rich, robust device which meets IEEE 802.3 standards over multiple temperature ranges from commercial to extreme temperatures. This device is ideally suited for harsh environments such as wireless remote base stations, automotive/transportation, and industrial control applications. It offers enhanced ESD protection and the choice of an MII or RMII interface for maximum flexibility in MPU selection; all in a 48 pin package. The DP83848VYB extends the leadership position of the PHYTER™ family of devices with a wide operating temperature range. The TI line of PHYTER transceivers builds on decades of Ethernet expertise to offer the high performance and flexibility that allows the end user an easy implementation tailored to

Additional Information:

• Item Code: TI084
• Production Capacity: 50000
• Delivery Time: 2-3 WEEKS
• Packaging Details: TRAY

Service Details:

CAN Interface IC SLEEP MODE1 Features 1• Single 3.3-V Supply Voltage • Bus Pins Fault Protection Exceeds ±36 V • Bus Pins ESD Protection Exceeds ±16 kV HBM • Compatible With ISO 11898-2 • GIFT/ICT Compliant • Data Rates up to 1 Mbps • Extended –7 V to 12 V Common Mode Range • High-Input Impedance Allows for 120 Nodes • LVTTL I/Os are 5-V Tolerant • Adjustable Driver Transition Times for Improved Emissions Performance • Unpowered Node Does Not Disturb the Bus • Low Current Standby Mode, 200-μA (Typical) • SN65HVD233: Loopback Mode • SN65HVD234: Ultra Low Current Sleep Mode – 50-nA Typical Current Consumption • SN65HVD235: Autobaud Loopback Mode • Thermal Shutdown Protection • Power up and Down With Glitch-Free Bus Inputs and Outputs – High-Input Impedance With Low VCC – Monolithic Output During Power Cycling 2 Applications • Industrial Automation, Control, Sensors, and Drive Systems • Motor and Robotic Control • Building and Climate Control (HVAC) • Backplane Communication and Control • CAN Bus Standards such as CANopen, DeviceNet, CAN Kingdom, NMEA 2000, SAE J1939 3 Description The SN65HVD233, SN65HVD234, and SN65HVD235 are used in applications employing the controller area network (CAN) serial communication physical layer in accordance with the ISO 11898 standard. As a CAN transceiver, each provides transmit and receive capability between the differential CAN bus and a CAN controller, with signaling rates up to 1 Mbps. Designed for operation in especially harsh environments, the devices feature cross-wire protection, overvoltage protection up to ±36 V, loss of ground protection, overtemperature (thermal shutdown) protection, and common-mode transient protection of ±100 V. These devices operate over a wide –7 V to 12 V common-mode range. These transceivers are the interface between the host CAN controller on the microprocessor and the differential CAN bus used in industrial, building automation, transportation, and automotive applications

Service Details:

Battery Management Li-Ion Switchmode Charge Management IC
Features  Safe charge of Li-Ion battery packs  Pulse-width modulation control for current and voltage regulation   Programmable high-side/low-side current-sense  Fast charge terminated by selectable minimum current; safety backup termination at maximum time  Pre-charge qualification detects shorted or damaged cells and conditions battery  Charging continuously qualified by temperature and voltage limits  Direct LED control outputs to display charge status and fault conditions General Description The bq2954 Li-Ion Charge-Management IC uses a flexible pulse-width modulation regulator to control voltage and current during charging. The regulator frequency is set by an external capacitor for design flexibility. The switch-mode design minimizes power dissipation. For safety, the bq2954 inhibits fast charging until the battery voltage and temperature are within configured limits. If the battery voltage is less than the low-voltage threshold, the bq2954 provides low-current conditioning of the battery. For charge qualifiction, the bq2954 uses an external thermistor to measure battery temperature. Charging begins when power is applied or the

Service Details:

16-Bit, Parallel Input Multiplying Digital-to-Analog Converter 2• ±0.5 LSB DNL • Automatic Test Equipment • ±1 LSB INL • Instrumentation • 16-Bit Monotonic • Digitally Controlled Calibration • Industrial Control PLCs • Low Noise: 10 nV/√Hz • Low Power: IDD = 2 µA • Analog Power Supply: +2.7 V to +5.5 V The DAC8820, a multiplying digital-to-analog • 1.66 mA Full-Scale Current, converter (DAC), is designed to operate from a single with VREF = 10 V 2.7 V to 5.5 V supply. • Settling Time: 0.5 µs The applied external reference input voltage VREF • 4-Quadrant Multiplying Reference determines the full-scale output current. An internal • Reference Bandwidth: 8 MHz feedback resistor (RFB) provides temperature tracking for the full-scale output when combined with an • Reference Input: ±15 V external, current-to-voltage (I/V) precision amplifier. • Reference Dynamics: –105 dB THD A parallel interface offers high-speed • SSOP-28 Package communications. The DAC8820 is packaged in a • Industry-Standard Pin Configuration space-saving SSOP-28 package and

Service Details:

LM2596 SIMPLE SWITCHER® Power Converter 150-kHz 3-A Step-Down Voltage Regulator 1 Features • New product available: LMR33630 36-V, 3-A, 400- kHz synchronous converter • 3.3-V, 5-V, 12-V, and adjustable output versions • Adjustable version output voltage range: 1.2-V to 37-V ±4% maximum over line and load conditions • Available in TO-220 and TO-263 packages • 3-A output load current • Input voltage range up to 40 V • Requires only four external components • Excellent line and load regulation specifications • 150-kHz Fixed-frequency internal oscillator • TTL shutdown capability • Low power standby mode, IQ, typically 80 μA • High efficiency • Uses readily available standard inductors • Thermal shutdown and current-limit protection • Create a custom design using the LM2596 with the WEBENCH Power Designer 2 Applications • Appliances • Grid infrastructure • EPOS • Home theater 3 Description The LM2596 series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator, capable of driving a 3-A load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3 V, 5 V, 12 V, and an adjustable output version. Requiring a minimum number of external components, these regulators are simple to use and include internal frequency compensation, and a fixedfrequency oscillator. The LM2596 series operates at a switching frequency of 150 kHz, thus allowing smaller sized filter components than what would be required with lower frequency switching regulators. Available in a standard 5-pin TO-220 package with several different lead bend options, and a 5-pin TO-263 surface mount package. The new product, LMR33630, offers reduced BOM cost, higher efficiency, and an 85% reduction in solution size among many other features. Start WEBENCH Design with the LMR33630. PART NUMBER PACKAGE(1) BODY SIZE (NOM) LM2596 TO-220 (5) 14.986 mm × 10.16 mm

Service Details:

3 Description 1• Signaling Rate > 50 Mbps ISO742x provide galvanic isolation up to 2500 VRMS for 1 minute per UL and 4242 VPK per VDE. These • Default Output 'High' and 'Low' Options devices have two isolated channels. Each channel • Low Power Consumption: Typical ICC per Channel has a logic input and output buffer separated by a (3.3-V Supplies): silicon dioxide (SiO2 ) insulation barrier. Used in conjunction with isolated power supplies, these – ISO7420: 1.4 mA at 1 Mbps, 2.5 mA at devices prevent noise currents on a data bus or other 25 Mbps circuit from entering the local ground and interfering – ISO7421: 1.8 mA at 1 Mbps, 2.8 mA at with or damaging sensitive circuitry. ISO7420 has 25 Mbps both channels in the same direction while ISO7421 • Low Propagation Delay: 7 ns Typical has the two channels in opposite direction. In case of input power or signal loss, default output is 'low' for • Low Pulse Skew: 200 ps Typical devices with suffix 'F' and 'high' for devices without • Wide TA Range Specified: –40°C to 125°C suffix 'F'. ISO742x have no integrated noise filter and • 50-KV/μs Transient Immunity, Typical thus have fast propagation delays. • Isolation Barrier Life: > 25 Years These devices have TTL input thresholds and • Operates from 3-V to 5.5-V Supply Levels operate from 3-V to 5.5-V supplies. All inputs are 5-V tolerant when supplied from a 3.3-V supply. • 3.3-V and 5-V Level Translation • Narrow Body SOIC-8 Package Device Information(1) • Safety and Regulatory Approvals: PART NUMBER PACKAGE BODY SIZE (NOM) – 4242 VPK Isolation per DIN V VDE V 0884-10 ISO7420E and DIN EN 61010-1 ISO7420FE SOIC (8) 4.90 mm x 3.91 mm – 2500 VRMS Isolation for 1 minute per UL 1577 ISO7421E – CSA Component Acceptance Notice 5A, IEC ISO7421FE 60950-1 and IEC 61010-1 Standards (1) For all available packages, see the orderable a

Service Details:

ISO724x High-Speed, Quad-Channel Digital Isolators 1 1 Features 1• 25 and 150-Mbps Signaling Rate Options – Low Channel-to-Channel Output Skew; 1 ns Maximum – Low Pulse-Width Distortion (PWD); 2 ns Maximum – Low Jitter Content; 1 ns Typ at 150 Mbps • Selectable Default Output (ISO7240CF) • > 25-Year Life at Rated Working Voltage (see High-Voltage Lifetime of the ISO72x Family of Digital Isolators and Isolation Capacitor Lifetime Projection) • 4-kV ESD Protection • Operates With 3.3-V or 5-V Supplies • High Electromagnetic Immunity (see ISO72x Digital Isolator Magnetic-Field Immunity) • –40°C to +125°C Operating Temperature Range • Safety-Related Certifications: – VDE 4000 VPK Basic Insulation per DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 – 2.5 kVRMS Insulation for 1 minute per UL 1577 – CSA Component Acceptance Notice #5A and IEC 60950-1 End Equipment Standard 2 Applications • Industrial Fieldbus • Computer Peripheral Interface • Servo Control Interface • Data Acquisition 3 Description The ISO7240x, ISO7241x, and ISO7242x devices are quad-channel digital isolators with multiple channel configurations and output-enable functions. These devices have logic-input and logic-output buffers separated by Texas Instrument’s silicon-dioxide (SiO2 ) isolation barrier. Used in conjunction with isolated power supplies, these devices help block high voltage, isolate grounds, and prevent noise currents from entering the local ground and interfering with or damaging sensitive circuitry. The ISO7240x family of devices has all four channels in the same direction. The ISO7241x family of devices has three channels in the same direction and one channel in the opposition direction. The ISO7242x family of devices has two channels in each direction. Device Information(1) PART NUMBER PACKAGE BODY SIZE (NOM) ISO7240CF SOIC (16) 10.30 mm × 7.50 mm ISO7240C ISO7240M ISO7241C ISO7241M ISO7242C ISO7242M (1) For all available packages, se

Service Details:

3 Description The ISO7240x, ISO7241x, and ISO7242x devices are quad-channel digital isolators with multiple channel configurations and output-enable functions. These devices have logic-input and logic-output buffers separated by Texas Instrument’s silicon-dioxide (SiO2 ) isolation barrier. Used in conjunction with isolated power supplies, these devices help block high voltage, isolate grounds, and prevent noise currents from entering the local ground and interfering with or damaging sensitive circuitry. The ISO7240x family of devices has all four channels in the same direction. The ISO7241x family of devices has three channels in the same direction and one channel in the opposition direction. The ISO7242x family of devices has two channels in each direction. Device Information(1) PART NUMBER PACKAGE BODY SIZE (NOM) ISO7240CF SOIC (16) 10.30 mm × 7.50 mm ISO7240C ISO7240M ISO7241C ISO7241M ISO7242C ISO7242M (1) For all available packages,

Service Details:

Features 1• Emulated Peak Current Mode • Wide Operating Range Up to 100 V • Low IQ Shutdown (< 10 µA) • Drives Standard or Logic Level MOSFETs • Robust 3.5-A Peak Gate Drive • Free-run or Synchronous Operation to 1 MHz • Optional Diode Emulation Mode • Programmable Output from 1.215 V to 80 V • Precision 1.5% Voltage Reference • Programmable Current Limit • Programmable Soft-Start • Programmable Line Undervoltage Lockout • Automatic Switch to External Bias Supply • HTSSOP-20 Exposed Pad • Thermal Shutdown • Create a Custom Design Using the LM5116 with the WEBENCH Power Designer 2 Applications • Automotive Infotainment • Industrial DC-DC Motor Drivers • Automotive USB Adapters • Telecom Servers 3 Description The LM5116 is a synchronous buck controller intended for step-down regulator applications from a high-voltage or widely varying input supply. The control method is based upon current mode control utilizing an emulated current ramp. Current mode control provides inherent line feed-forward, cycle-bycycle current limiting, and ease-of-loop compensation. The use of an emulated control ramp reduces noise sensitivity of the pulse-width modulation circuit, allowing reliable control of very small duty cycles necessary in high-input voltage applications. The operating frequency is programmable from 50 kHz to 1 MHz. The LM5116 drives external high-side and low-side NMOS power switches with adaptive dead-time control. A user-selectable diode emulation mode enables discontinuous mode operation, for improved efficiency at light load conditions. A low quiescent current shutdown disables the controller and consumes less than 10 µA of total input current. Additional features include a high-voltage bias regulator, automatic switch-over to external bias for improved efficiency, thermal shutdown, frequency synchronization, cycle-by-cycle current limit, and adjustable line undervoltage lockout. The device is available in a power enhanced HTSSOP-20 package featuring an exposed die attach pad to aid thermal dissipation. Device Information(1) PART NUMBER PACKAGE BODY SIZE (NOM) LM5116 HTSSOP (20) 6.50 mm × 4.40 mm (1) For all available packages, see the ordera

Service Details:

1 Features 1• 100 Mbps data rate • Robust isolation barrier: – >100-year projected lifetime at 1500 VRMS working voltage – Up to 5000 VRMS isolation rating – Up to 12.8 kV surge capability – ±100 kV/μs typical CMTI • Wide supply range: 2.25 V to 5.5 V • 2.25-V to 5.5-V level translation • Default output high (ISO774x) and low (ISO774xF) options • Wide temperature range: –55°C to 125°C • Low power consumption, typical 1.5 mA per channel at 1 Mbps • Low propagation delay: 10.7 ns typical (5-V Supplies) • Robust electromagnetic compatibility (EMC) – System-level ESD, EFT, and surge immunity – ±8 kV IEC 61000-4-2 contact discharge protection across isolation barrier – Low emissions • Wide-SOIC (DW-16) and QSOP (DBQ-16) package options • Automotive version available: ISO774x-Q1 • Safety-related certifications: – DIN VDE V 0884-11:2017-01 – UL 1577 component recognition program – CSA, CQC, and TUV certifications 2 Applications • Industrial automation • Motor control • Power supplies • Solar inverters • Medical equipment 3 Description The ISO774x devices are high-performance, quadchannel digital isolators with 5000 VRMS (DW package) and 3000 VRMS (DBQ package) isolation ratings per UL 1577. This family includes devices with reinforced insulation ratings according to VDE, CSA, TUV and CQC. The ISO7741B device is designed for applications that require basic insulation ratings only. The ISO774x devices provide high electromagnetic immunity and low emissions at low power consumption, while isolating CMOS or LVCMOS digital I/Os. Each isolation channel has a logic input and output buffer separated by a double capacitive silicon dioxide (SiO2 ) insulation barrier. These devices come with enable pins which can be used to put the respective outputs in high impedance for multi-master driving applications and to reduce power consumption. The ISO7740 device has all four channels in the same direction, the ISO7741 device has three forward and one reverse-direction channels, and the ISO7742 device has two forward and two reverse-direction channels. If the input power or signal is lost, default output is high for devices without suffix F and low for devices with suffix F. See the Device Functional Modes section for further details. Device Information(1) PART NUMBER PACKAGE BODY SIZE (NOM) ISO7740 ISO7741 ISO7742 SOIC (DW) 10.30 mm × 7.50 mm SSOP (DBQ) 4.90 mm × 3.90 mm ISO7741B SOIC (DW) 10.30 mm × 7.50 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Simp

Service Details:

Switching Voltage RegulatorsLM22677/-Q1 42-V, 5-A SIMPLE SWITCHER® , Step-Down Voltage Regulator With Features• Wide Input Voltage Range: 4.5 V to 42 V functions necessary to implement an efficient high- • Internally Compensated Voltage Mode Control voltage step-down (buck) regulator using a minimum • Stable With Low ESR Ceramic Capacitors of external components. This easy-to-use regulator • 100-mΩ N-Channel MOSFET incorporates a 42-V N-channel MOSFET switch that can provide up to 5 A of load current. Excellent line • Output Voltage Options: and load regulation along with high efficiency (> 90%) – -ADJ (Outputs as Low as 1.285 V) are featured. Voltage mode control offers short – -5.0 (Output Fixed to 5 V) minimum on-time, allowing the widest ratio between input and output voltages. Internal loop compensation • ±1.5% Feedback Reference Accuracy means that the user is free from the tedious task of • 500-kHz Default Switching Frequency calculating the loop compensation components. Fixed • Adjustable Switching Frequency and 5-V output and adjustable output voltage options are Synchronization available. The default switching frequency is set at 500 kHz, thus allowing for small external components • –40°C to +125°C Operating Juncti

Additional Information:

• Item Code: HHUNJKBJ
• Production Capacity: 50000
• Delivery Time: 2 WEEKS
• Packaging Details: ESD

Service Details:

DACx760 Single-Channel, 12- and 16-Bit Programmable Current and Voltage Output Digital-to-Analog Converters for 4-mA to 20-mA Current-Loop Applications 1 Features • Current output: 4 mA to 20 mA; 0 mA to 20 mA; 0 mA to 24 mA • Voltage output: – 0 V to 5 V; 0 V to 10 V; ±5 V; ±10 V – 0 V to 5.5 V; 0 V to 11 V; ±5.5 V; ±11 V (10% overrange) • ±0.1% FSR total unadjusted error (TUE) maximum • DNL: ±1 LSB maximum • Simultaneous voltage and current output • Internal 5-V reference (10 ppm/°C, maximum) • Internal 4.6-V power-supply output • Reliability features: – CRC check and watchdog timer – Thermal alarm – Open alarm, short current limit • Wide temperature range: –40°C to 125°C • Packages: 6-mm × 6-mm 40-pin VQFN and 24-pin 3 Description The DACx760 are precision, fully integrated, 12- bit and 16-bit digital-to-analog converters (DACs) designed to meet the requirements of industrial process-control applications. These devices are programmable as a current output with a range of 4 mA to 20 mA, 0 mA to 20 mA, or 0 mA to 24 mA; or as a voltage output with a range of 0 V to 5 V, 0 V to 10 V, ±5 V, or ±10 V with a 10% overrange (0 V to 5.5 V, 0 V to 11 V, ±5.5 V, or ±11 V). Both current and voltage outputs can be simultaneously enabled while being controlled by one data register. These devices include a power-on-reset function for powering up in a known state (both IOUT and VOUT are disabled and in a Hi-Z state). The CLR and CLR- SEL pins set the voltage outputs to zero-scale or midscale, and the current output to the low end of the range if the output is enabled. Zero and gain registers can be programmed to digitally calibrate the device in the end system. The output slew rate is also programmable by register. These devices can superimpose an external HART® signal on the current output, and operate with either a single 10-V to 36-V

Service Details:

SNx5HVD251Industrial CANBusTransceiver 3 Description 1 Drop-In Improved Replacement for the PCA82C250 and PCA82C251  Bus-Fault Protection of  36 V  Meets or Exceeds ISO 11898  Signaling Rates(1) up to 1 Mbps  High Input Impedance Allows up to 120 Nodes on a Bus  Bus Pin ESD Protection Exceeds 14 kV HBM  Unpowered Node Does Not Disturb the Bus  Low-Current Standby Mode: 200 A Typical  Thermal Shutdown Protection  Glitch-Free Power-Up and Power-Down CAN Bus Protection for Hot-Plugging  DeviceNet Vendor ID #806 (1) 2 Applications   CAN Data Buses  Industrial Automation  SAE J1939 Standard Data Bus Interface  NMEA 2000 Standard Data Bus Interface The HVD251 is intended for use in applications employing the Controller Area Network (CAN) serial communication physical layer in accordance with the ISO 11898 Standard. The HVD251 provides differential transmit capability to the bus and differential receive capability to a CAN controller at speeds up to 1 megabits per second (Mbps). Designed for operation in harsh environments, the device features cross-wire, overvoltage and loss of ground protection to  36 V. Also featured are overtemperature protection as well as  7-V to 12-V common-mode range, and tolerance to transients of  200 V. The transceiver interfaces the single-ended CAN controller with the differential CAN bus found in industrial, building automation, and automotive applications. Rs, pin 8, selects one of three different modes of operation: high-speed, slope control, or low-power mode. The high-speed mode of operation is selected by connecting pin 8 to ground, allowing the transmitter output transistors to switch as fast as possible with no limitation on the rise and fall slope. The rise and fall slope can be adjusted by connecting a resistor to ground at pin 8; the slope is proportional to the pin's output current. Slope control with an external resistor value of 10 k gives about 15-V /  s slew rate; 100 k gives about 2-V s slew rate. If a high logic level is applied to the Rs pin 8, the device enters a low-current standby mode where the driver is switched off and the receiver remains active. The local protocol controller returns the device to the

Service Details:

LDO Voltage Regulators 800mA Low-Dropout Linear Regulator 4-SOT-223 -40 to 125

Service Details:

Switching Voltage Regulators Lo Noise Negative Bias GeneratorRegulated Output Voltage −0.232 V • Output Voltage Tolerance 5% • Output Voltage Ripple 4 mVPP • Supply Voltage 3 V to 5.25 V • Conversion Efficiency Up to 98% • Quiescent Current 78 µA • Shutdown Current 20 nA • Turnon Time 500 µs • Operating Temperature Range −40°C to 125°C • 8-Pin VSSOP Package 2 Applications • True Zero Amplifier Outputs • Portable Instrumentation • Low-Voltage Split-Power Supplies

Service Details:

Low-Noise, Low-Distortion INSTRUMENTATION AMPLIFIER APPLICATIONS ??? PROFESSIONAL MICROPHONE PREAMPS ??? MOVING-COIL TRANSDUCER AMPLIFIERS ??? DIFFERENTIAL RECEIVERS ??? BRIDGE TRANSDUCER AMPLIFIERS FEATURES ??? LOW NOISE: 1nV/√Hz at 1kHz ??? LOW THD+N: 0.002% at 1kHz, G = 100 ??? WIDE BANDWIDTH: 800kHz at G = 100 ??? WIDE SUPPLY RANGE: ±4.5V to ±18V ??? HIGH CMR: > 100dB ??? GAIN SET WITH EXTERNAL RESISTOR ??? SO-14 SURFACE-MOUNT PACKAGE DESCRIPTION The INA163 is a very low-noise, low-distortion, monolithic instrumentation amplifier. Its current-feedback circuitry achieves very wide bandwidth and excellent dynamic response over a wide range of gain. It is ideal for low-level audio signals such as balanced lowimpedance microphones. Many industrial, instrumentation, and medical applications also benefit from its low noise and wide bandwidth. Unique distortion cancellation circuitry reduces distortion to extremely low levels, even in high gain. The INA163 provides near-theoretical noise performance for 200??? source impedance. Its differential input, low noise, and low distortion provide superior performance in professional microphone amplifier applications. The INA163’s wide supply voltage, excellent output voltage swing, and high output current drive allow its use in high-level audio stages as well. The INA163 is available in a space-saving SO-14 surface-mount package, specified for operation over the –40°C to +85°C temperatur

Service Details:

32-bit Microcontrollers - MCU Piccolo Microcntroller
1 Features • High-efficiency 32-bit CPU (TMS320C28x) – 60 MHz (16.67-ns cycle time) – 16 × 16 and 32 × 32 MAC operations – 16 × 16 dual MAC – Harvard bus architecture – Atomic operations – Fast interrupt response and processing – Unified memory programming model – Code-efficient (in C/C++ and Assembly) • Programmable Control Law Accelerator (CLA) – 32-bit floating-point math accelerator – Executes code independently of the main CPU • Endianness: Little endian • JTAG boundary scan support – IEEE Standard 1149.1-1990 Standard Test Access Port and Boundary Scan Architecture • Low cost for both device and system: – Single 3.3-V supply – No power sequencing requirement – Integrated power-on reset and brown-out reset – Low power – No analog support pins • Clocking: – Two internal zero-pin oscillators – On-chip crystal oscillator and external clock input – Watchdog timer module – Missing clock detection circuitry • Up to 45 individually programmable, multiplexed GPIO pins with input filtering • Peripheral Interrupt Expansion (PIE) block that supports all peripheral interrupts • Three 32-bit CPU timers • Independent 16-bit timer in each Enhanced Pulse Width Modulator (ePWM) • On-chip memory – Flash, SARAM, OTP, Boot ROM available • Code-security module • 128-bit security key and lock – Protects secure memory blocks – Prevents firmware reverse engineering • Serial port peripherals – One Serial Communications Interface (SCI) Universal Asynchronous Receiver/Transmitter (UART) module – Two Serial Peripheral Interface (SPI) modules – One Inter-Integrated-Circuit (I2C) module – One Local Interconnect Network (LIN) module – One Enhanced Controller Area Network (eCAN) module • Enhanced control peripherals – ePWM – High-Resolution PWM (HRPWM) – Enhanced Capture (eCAP) module – High-Resolution Input Capture (HRCAP) module – Enhanced Quadrature Encoder Pulse (eQEP) module – Analog-to-Digital Converter (ADC) – On-chip temperature sensor – Comparator • Advanced emulation features – Analysis and breakpoint functions – Real-time debug through hardware • Package options – 56-Pin RSH Very Thin Quad Flatpack (No lead) (VQFN) – 64-Pin PAG Thin Quad Flatpack (TQFP) – 80-Pin PN Low-Profile Quad Flatpack (LQFP) • Temperature options – T: –40°C to 105°C – S: –40°C to 125°C – Q: –40°C to 125°C (AEC Q100 qualification for auto

Service Details:

OPAx22x High Precision, Low Noise Operational Amplifiers 1 Features 3 Description 1 The OPAx22x series operational amplifiers combine • Low Noise: 3nV/√Hz low noise and wide bandwidth with high precision to • Wide Bandwidth: make them the ideal choice for applications requiring – OPA227: 8 MHz, 2.3 V/μs both AC and precision DC performance. – OPA228: 33 MHz, 10 V/μs The OPAx227 is unity-gain stable and features high • Settling Time: 5 μs slew rate (2.3V/µs) and wide bandwidth (8MHz). The (Significant Improvement Over OP-27) OPAx228 is optimized for closed-loop gains of 5 or greater, and offers higher speed with a slew rate of • High CMRR: 138 dB 10V/µs and a bandwidth of 33MHz. • High Open-loop Gain: 160 dB The OPAx227 and OPAx228 series operational • Low Input Bias Current: 10 nA Maximum amplifiers are ideal for professional audio equipment. • Low Offset Voltage: 75 µV Maximum In addition, low quiescent current and low cost make • Wide Supply Range: ±2.5 V to ±18 V them ideal for portable applications requiring high precision. • OPA227 Replaces OP-27, LT1007, MAX427 • OPA228 Replaces OP-37, LT1037, MAX437 The OPAx227 and OPAx228 series operational amplifiers are pin-for-pin replacements for the • Single, Dual, and Quad Versions industry standard OP-27 and OP-37 with substantial improvements across the board. The dual and quad 2 Applications versions are available for space savings and per • Data Acquisition channel cost reduction. • Telecom Equipment The OPAx227, OPAx228, are available in DIP-8 and • Geophysical Analysis SO-8 packages. The OPA4227 and OPA4228 are available in DIP-14 and SO-14 packages with • Vibration Analysis standard pin configurations. Operation is specified • Spectral Analysis from –40°C to 85°C. • Professional Audio Equipment Device Information(1) • Active Filters PART NUMBER PACKAGE BODY SIZE (NOM) • Power Supply Controls OPA227 PDIP (8) 9.81 mm × 6.35 mm Input Referred Noise OPA228 SOIC (8) 4.90 mm × 3.91 mm OPA2227 PDIP (8) 9.81 mm × 6.35 mm OPA2228 SOIC (8) 4.90 mm × 3.91 mm OPA4227 PDIP (14) 19.30 mm × 6.35 mm OPA4228 SOIC (14) 8.65 mm × 3.91 mm (1) For all available packages, see the orderable addend

Service Details:

Supply Current . . . 23 µA/Channel
Gain-Bandwidth Product . . . 220 kHz
Output Drive Capability . . . ±10 mA
Input Offset Voltage . . . 20 µV (typ)
VDD Range . . . 2.7 V to 6 V
Power Supply Rejection Ratio . . . 106 dB
Ultralow-Power Shutdown Mode IDD . . . 16 nA/ch
Rail-To-Rail Input/Output (RRIO)
Ultrasmall Packaging − 5 or 6 Pin SOT-23 (TLV2450/1) − 8 or 10 Pin MSOP (TLV2452/3) description The TLV245x is a family of rail-to-rail input/output operational amplifiers that sets a new performance point for supply current and ac performance. These devices consume a mere 23 µA/channel while offering 220 kHz of gain-bandwidth product, much higher than competitive devices with similar supply current levels. Along with increased ac performance, the amplifier provides high output drive capability, solving a major shortcoming of older micropower rail-to-rail input/output operational amplifiers. The TLV245x can swing to within 250 mV of each supply rail while driving a 2.5-mA load. Both the inputs and outputs swing rail-to-rail for increased dynamic range in low-voltage applications. This performance makes the TLV245x family ideal for portable medical equipment, patient monitoring systems, and data acquisition circuits. FAMILY PACKAGE T

Service Details:

1 Features 1• Meets or Exceeds TIA/EIA-232-F and ITU Recommendation V.28 • Operates From a Single 5-V Power Supply With 1.0-µF Charge-Pump Capacitors • Operates up to 120 kbit/s • Two Drivers and Two Receivers • ±30-V Input Levels • Low Supply Current: 8 mA Typical • ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-A) • Upgrade With Improved ESD (15-kV HBM) and 0.1-µF Charge-Pump Capacitors is Available With the MAX202 Device 2 Applications • TIA/EIA-232-F • Battery-Powered Systems • Terminals • Modems • Computers 3 Description The MAX232 device is a dual driver/receiver that includes a capacitive voltage generator to supply TIA/EIA-232-F voltage levels from a single 5-V supply. Each receiver converts TIA/EIA-232-F inputs to 5-V TTL/CMOS levels. These receivers have a typical threshold of 1.3 V, a typical hysteresis of 0.5 V, and can accept ±30-V inputs. Each driver converts TTL/CMOS input levels into TIA/EIA-232-F levels. Device Information(1) ORDER NUMBER PACKAGE (PIN) BODY SIZE MAX232x SOIC (16) 9.90 mm × 3.91 mm SOIC (16) 10.30 mm × 7.50 mm PDIP (16) 19.30 mm × 6.35 mm SOP (16) 10.3 mm × 5.30 mm (1) For all available packages, se

Service Details:

32-bit Microcontrollers - MCU C2000 32-bit MCU with 400 MIPS, 1xCPU, 1xCLA, FPU, TMU, 1024 KB flash, EMIF, 16b ADC 176-HLQFP -40 to 1051 Features • TMS320C28x 32-bit CPU – 200 MHz – IEEE 754 single-precision Floating-Point Unit (FPU) – Trigonometric Math Unit (TMU) – Viterbi/Complex Math Unit (VCU-II) • Programmable Control Law Accelerator (CLA) – 200 MHz – IEEE 754 single-precision floating-point instructions – Executes code independently of main CPU • On-chip memory – 512KB (256KW) or 1MB (512KW) of flash (ECC-protected) – 132KB (66KW) or 164KB (82KW) of RAM (ECC-protected or parity-protected) – Dual-zone security supporting third-party development – Unique identification number • Clock and system control – Two internal zero-pin 10-MHz oscillators – On-chip crystal oscillator – Windowed watchdog timer module – Missing clock detection circuitry • 1.2-V core, 3.3-V I/O design • System peripherals – Two External Memory Interfaces (EMIFs) with ASRAM and SDRAM support – 6-channel Direct Memory Access (DMA) controller – Up to 169 individually programmable, multiplexed General-Purpose Input/Output (GPIO) pins with input filtering – Expanded Peripheral Interrupt controller (ePIE) – Multiple Low-Power Mode (LPM) support with external wakeup • Communications peripherals – USB 2.0 (MAC + PHY) – Support for 12-pin 3.3 V-compatible Universal Parallel Port (uPP) interface – Two Controller Area Network (CAN) modules (pin-bootable) – Three high-speed (up to 50-MHz) SPI ports (pin-bootable) – Two Multichannel Buffered Serial Ports (McBSPs) – Four Serial Communications Interfaces (SCI/ UART) (pin-bootable) – Two I2C interfaces (pin-bootable) • Analog subsystem – Up to four Analog-to-Digital Converters (ADCs) • 16-bit mode – 1.1 MSPS each (up to 4.4-MSPS system throughput) – Differential inputs – Up to 12 external channels • 12-bit mode – 3.5 MSPS each (up to 14-MSPS system throughput) – Single-ended inputs – Up to 24 external channels • Single Sample-and-Hold (S/H) on each ADC • Hardware-integrated post-processing of ADC conversions – Saturating offset calibration – Error from setpoint calculation – High, low, and zero-crossing compare, with interrupt capability – Trigger-to-sample delay capture – Eight windowed comparators with 12-bit Digitalto-Analog Converter (DAC) references – Three 12-bit buffered DAC outputs • Enhanced control peripherals – 24 PWM channels with enhanced features – 16 High-Resolution Pulse Width Modulator (HRPWM) channels • High resolution on both A and B channels of 8 PWM modules • Dead-band support (on both standard and high resolution) – Six Enhanced Capture (eCAP) modules – Three Enhanced Quadrature Encoder Pulse (eQEP) modules – Eight Sigma-Delta Filter Module (SDFM) input channels, 2 parallel filters per channel • Standard SDFM data filtering • Comparator filter for fast action for out of range • Configurable Logic Block (CLB) – Augments existing peripheral capability – Supports position manager solutions • Functional Safety-Compliant www.ti.com TMS320F28379S, TMS320F28378S, TMS320F28377S, TMS320F28377S-Q1 TMS320F28376S, TMS320F28375S, TMS320F28375S-Q1, TMS320F28374S SPRS881J – AUGUST 2014 – REVISED FEBRUARY 2021 Copyright © 2021 Texas Instruments Incorporated Submit Document Feedback 1 Product Folder Links: TMS320F28379S TMS320F28378S TMS320F28377S TMS320F28377S-Q1 TMS320F28376S TMS320F28375S TMS320F28375S-Q1 TMS320F28374S TMS320F28379S, TMS320F28378S, TMS320F28377S, TMS320F28377S-Q1 TMS320F28376S, TMS320F28375S, TMS320F28375S-Q1, TMS320F28374S SPRS881J – AUGUST 2014 – REVISED FEBRUARY